|
|
 |
.
Stainless-Steel Trailer
Parts
For a quick search, we are going to try to list
our entire offering of stainless steel parts &
accessories in
this column.
|
|
D-Ring,
1 bolt, Stainless Steel
|
 |
This D-ring will come in
handy if you only want to put one hole in your trailer
instead of two. The mounting bracket is folded over the
ring, so the bolt goes through both sides. The D-ring is
3/8" D, and both pieces are non-polished stainless
steel. 1200 lb. breaking strength. Ring is 1 7/8" W X
1 5/8" L. Bracket is 1"
X 1". Use to fasten feed bags and ropes. Not for
tying horses! 1 bolt stainless steel |
|
D-Ring,
1 Bolt, stainless steel |
|
|
|
|
Door Holder-2 piece
set in 3 sizes, Stainless Steel |
 |
Door Holder-2 piece set
The plunger
installs on the door side, and the nylon receiver end
installs on the trailer body. Mounting holes for the
plunger side are 1 9/32" apart, measured center to
center. Install white nylon receiver with one sheet
metal screw. Three sizes available, measured by tip of plunger
to trailer wall.
*Install both door holders &
receivers with #12 X 1" sheet metal screws or a #10
machine screw & jack nut, available on the fastener
page. The white hard nylon
receiver socket is rated at a
30
lb. pull.
Steel/Zinc door holders & the
white nylon receiver are also sold on the
Door Holder page.. |
|
Door
Holder-2 piece set 1" Stainless Steel |
|
|
|
Door
Holder-2 piece set 2" Stainless Steel |
|
|
|
Door
Holder-2 piece set 3" Stainless Steel |
|
|
|
Door
Holder-2 piece set 4" Stainless Steel |
|
|
|
|
Stainless
Steel Positive Door Holder |
 |
Stainless Steel
Positive Door Holder w/ Bracket
2 Piece Set. The wire hook installs on
the trailer door, and the bracket installs
on the trailer wall. This will hold the door
open until released by hand. Wire hook folds
flush to the trailer door when not in use.
Can be installed on aluminum surfaces. Choice of: 4" or 6" wire hook
& bracket in stainless steel.
*Fastens
to trailer with eight #8 or #10
sheet metal screws per set, available on
the Fastener page.
|
|
4" Positive Door Holder w/ Bracket, S. Steel |
|
|
|
6" Positive Door Holder w/ Bracket, S. Steel |
|
|
|
|
|
|
THE
COLLAR Coupler Lock, in stainless steel |
(example of THE COLLAR &
padlock on a sliding-collar type coupler.) |
The Collar is
a anti-theft device for sliding-collar type
trailer hitches. It provides 24 hour
protection against trailer theft since you use
it both when the
trailer is attached to or detached from the towing
vehicle. It never gets lost, since it is always
kept on the trailer. A quality product, cast out
of stainless steel, it weighs nearly 1 1/2 lbs,
and will never rust.
The curved design resists physical damage , such
as hammering or sawing. The hole where the hinge
pin is inserted are welded shut and allow the
hinge pin to "float" in order to to
resist drilling. The Collar will work with an
assortment of different padlocks, allowing the
owner to key locks alike. Sold with a 70 MM
stainless steel round padlock below for $10.00
more. Multiple orders will have all padlocks
keyed alike. Designed to fit all BULLDOG bumper-pull
couplers, and many Kodiak & Butler
couplers.
THE COLLAR Coupler Lock:
choose with or without a 70 mm round stainless
steel padlock
|
|
THE
COLLAR Coupler Lock |
|
|
|
THE
COLLAR & Round Padlock |
|
|
|
|
|
|
Round
Stainless Steel Padlock,
70mm |
 |
A rugged stainless steel
padlock. Makes it very difficult
for bolt cutters or saws to get a grip when it's
fastened to your trailer lock. 2 3/4" across. Weighs 1/2 lb. Comes with 2
keys.
*suggested retail price in stores is
$14.95 & we've seen them as high as $19.95. *See
discount on
Trailer Locks page for multiples of two or three padlocks
keyed alike. |
|
70mm
(2 3/4") Round Stainless Steel Padlock |
|
|
|
|
|
Flush Mount Latches,
locking & non-locking in stainless steel |
  |
Also known as a Junior-size
Paddle Latch, it's the standard size for
replacing a door handle and latch in one piece on a
one-thickness trailer door. A sliding bolt is attached to
the back. Comes standard with 4 holes. Does not need to
be painted. These door latches
all stainless steel. The indentical zinc/steel
latches are found on the
Door Latch page.
Outer measurement: 4 3/4" tall X 3 5/8" wide
Hole (in trailer door) size: 3 3/4"X 2 3/4"
*Flush-Mount Latch neoprene gasket sold
on the Door Latch
page.
|
|
Flush Mount Latch, Locking w/Key, Stainless Steel |
|
|
|
Flush Mount Latch, Locking
w/Key, w/ Inside Release, Stainless Steel |
|
|
|
Flush Mount Latch,
Stainless Steel (non-locking)
|
|
|
Strap
Hinge, 4K, Stainless Steel |
Above is the new stainless
steel strap hinge
This is the comparison,
with the stainless steel strap hinge on the
bottom & the chrome strap hinge on the
top---the smaller side is the same hole
pattern, but see the hole placement difference
(1/4") on the long
side?
The holes
are also slightly larger--- these take a #12
screw, the chrome strap hinges take a #10
screw. |
Tired of replacing broken
chrome strap hinges?
Super-strong, these
stainless steel flush-mount strap hinges are
sold to replace the chrome strap hinges that look similar--but these have a
slightly different hole pattern.
For replacing
latches on tack room doors, tack
compartments and drop-down windows.They are made of
highly polished
stainless steel, with a steel pin & nylon
bushing. The hole pattern on the base of the
hinge matches exactly. On the longer side,
which would be fastened to the window or
door itself, the holes are located slightly
beyond the existing holes of the 4K chrome
strap hinge. The hinge covers the old holes
nicely, but you will have to drill 3 new
holes if you want this to be your
replacement hinge. The holes are also
slightly larger--- these take a #12 screw.
For application underneath a drop-down
window or tack door with the hinges
placed on the bottom, the head of the hinge
pin should be placed at the outside of the
window. So you will order a right and left.
For application on a tack
room door, if the hinges are on the
right
side of the door, you need a right on the
top and a left on the bottom (your choice
for
the for the center hinge).
A tack room door with the
hinges on the left would have the opposite
application.
Total Length is 5 5/8". |
|
Strap Hinge, 4K, Stainless Steel, pin head
on RIGHT |
|
|
|
Strap Hinge, 4K, Stainless Steel, pin head
on LEFT |
|
|
|
|
|
Product
Name Here
|
|
Pic Here |
Description Here |
|
Product Name Here |
|
|
|
|
Product
Name Here
|
|
Pic Here |
Description Here |
|
Product Name Here |
|
|
|
This page is a work in
progress......all of our stainless steel products are listed
on their individual pages elsewhere on the site. |
|
